20 Resources That Will Make You More Efficient With Double Glazing Door Lock Repairs
20 Resources That Will Make You More Efficient With Double Glazing Door Lock Repairs
Blog Article
Double Glazing Door Lock Repairs
Are your uPVC door or window mechanism not working properly? Perhaps the door or window handles aren't able to connect properly or are hard to use.
It's important that your double glazed doors function smoothly, or else you'll be wasting energy and increase the chance of burglary. Owen the Locksmith can fix your door lock at an affordable price.
Snapped Key
It can be quite frustrating when a key gets stuck into the lock. It could also be a security risk, as the door may not be locked and leave you vulnerable to burglars. There are a few quick fixes you can make to fix the problem and get your door working again.
First, remember to stay calm. If you panic you could end up pushing the broken key piece further into the lock.
Spray WD-40, or another penetrating oil, into the lock. This will assist the broken piece to emerge more easily. You can also use a screwdriver to help break pieces that could be blocking the way. If you're lucky enough to have a little bit of the key sticking out, you can make use of a paperclip or other thin metal object to grab it and pull it out. Both methods work, but be careful not to push the damaged key piece further into the keyway.
Some paperclips have grooved edges, which can be used as a hook extractor and jigsaw blades are also suitable for this use. If you don't have one of these tools, you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers can be used to grip and pull out the last part of the broken key.
If you cannot remove the broken piece of key, use a lock deicer. It's usually available at all hardware stores. It is used to freeze any moisture or ice that might be inside the lock.
If none of these solutions work, it might be time to consult a locksmith. Fitlocks experts can solve problems like broken handles or snapped keys with uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms so that they are easier to operate. Book a double glazing repair through us online, or give us a phone call to discuss your needs.
Broken Cylinder
A broken cylinder can pose a major security risk. It's fortunately a simple repair for professional locksmiths to complete. A locksmith must tap the cylinder in order to fix it. This can be accomplished with a hammer or other tool. However, the best method is to employ a wire or long match. The match or wire's end in the keyway. The locksmith will then strike the lock in order to crack it. This is more secure than using the hammer, which could damage the lock.
Overheating is the primary cause of cylinder heads cracking. This can happen when the block and cylinder head are made of various metals, such as cast-iron or aluminium. When the different metals heat up and cool down at different rates, it could create hotspots locally that expand faster than the rest of the head of the cylinder, leading to cracks.
Another possible cause of cracks in cylinders is corrosion. If the head and block of a cylinder are not maintained properly, they can rust or corrode, which can cause them to expand faster than expected. In time, this could also cause cracks.
If your uPVC window lock or door is brittle or requires a lot of pressure to turn, it can be the result of several things. A malfunctioning locking mechanism, misalignment, or a worn handle are common reasons for this issue.
Fortunately it double glazed windows near me is a simple and cost-effective fix for the majority of double glazing owners. A professional locksmith will usually be able to solve this problem within an hour of arriving at your property. Depending on your needs they can change the locking mechanism, change the window handles, and also change the gearboxes. A locksmith with experience can always advise you on the most cost-effective options for your home. They can even recommend upgrades to the highest-security 3 Star euro cylinders TS007 that provide an extra layer of protection against burglars. This is a small cost to pay for the security that comes from knowing your uPVC doors are secure.
Broken Handle
Window handle locks have intricate mechanisms that wear out with time and use, so it's no surprise they occasionally break. If yours breaks, it can be difficult to determine the source of the issue. Make sure you fix it correctly.
If the issue is with the internal locking mechanism or the latch, fixing your broken handle can improve your uPVC double glazing door's security as well as help you to stop draughts. It is costly to repair or replace the handle in a way that isn't done correctly. It could also harm the frame and lock of your door.
Screwdriver: With the window open and the screw loose, loosen the handle. The screw should be on the inside of the backplate, which is usually concealed by a screw cap for aesthetic reasons. Be sure to not lose any of the internal components inside the handle, such as the plates or levers on either side of the spindle. Ideally, keep them in the same order so you can re-install them in the event of a need.
Then, turn the handle so it's at 90 degrees to the window frame. Finally, loosen the screw on the back of the handle which holds it to the internal spindle using a second screwdriver. Once the screw is loose, you more info can pull the handle out and take the broken spindle out. Replace it with a new spindle, making sure it's the same length (you can find them online or get more info in hardware stores). Screw it into place. Be cautious not to overtighten because this could damage the handle or the window frame.
Close the handle and try it. The hope is that it will function smoothly and you'll be able open your window again.
While you're working double glazed near me on the handle, be sure to check your uPVC windows are shut properly. If they're not check here closing properly then you may experience draughts and damp in your home as well as compromising your home's energy efficiency. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they shut correctly.
Broken Spindle
It is often the case that the spindle in a handle breaks rather than the handle itself. This is especially common with uPVC tilt-and-turn windows. These types of windows require a handle that operates a locking mechanism in the window frame. The handle is connected to a centre rod that in turn activates cams that look like mushrooms, they secure the frame of the window. If the dead latch mechanism does not open when the handle is turned, it is possible that the spindle has broken, this can be an extremely frustrating issue.
Luckily there are options to rectify this issue. A good locksmith can quickly and effectively fix the issue. They can take apart the window handle using a tool to remove the wheel component of the mechanism, where the spindle goes. This can be done without causing any damage to the handle or causing other damage to the frame of the window.
After the wheel has been removed the technician can then inspect the spindle to determine what caused it to break. This involves disassembling the spindle and examining every component, observing any wear or damage. This process is usually carried out by technicians in a clean environment.
Next, clean the damaged spindle. This will remove any debris or dirt that might be preventing it from working normally. The spindle can then be repaired or replaced. If the technician is replacing the spindle, the dowel can be used that is similar in size to the original. The technician will then make holes in the same way into both pieces. This ensures that the new spindle is a precise fit with the handle.
If the spindle is damaged and cannot be repaired, it could require replacement. Home centers can sell generic replacements however if your window style is rare, you will require contacting an expert in cabinet making or woodworking who can replicate the exact part. Once the spindle has been installed, it can be fixed to the handle. The screw holes on the handle with the screws that are already in the frame. Once the handle is firmly set, you are able to operate your uPVC windows.